- Echo Audiofire 4 Driver For Mac Catalina
- Echo Audiofire 12
- Echo Audiofire 4 Driver For Mac Catalina
- Audiofire 12 Manual
- Echo Audiofire 4 Driver For Mac Pro
- Echo Audiofire 4 Driver For Mac Os
I used to own a Tascam FW-1082 but after a little while I realised I almost never used it’s motorised faders and that, despite being a really good audio interface, it was using too much real estate on my desk.
After some research, I decided to replace the FW-1082 with a Frontier Design Tranzport and an Audiofire 4 sound interface from Echo.
Echo Audiofire 4 Driver For Mac Catalina
Here are the Audiofire 4’s main features:
![For For](/uploads/1/2/7/7/127769931/260273472.jpg)
- 24 bit 96kHz
- Hardware monitoring
- 4 analog inputs (2 XLR/jack combos at the front, 2 balanced line in at the back)
- 4 balanced outputs at the back
- SPDIF I/O (effectively making the Audiofire 4 a 6 in / 6 out device!)
- MIDI I/O
- Headphone socket at the front + volume knob
- Mac OS: Core Audio + Core Midi native
- Windows XP + Vista: Asio 2.0, WDM, GSIF 2.0
- Firewire 400 (bus powered, optional 12VDC adaptor socket at the back)
The Audiofire 4 is built like a tank (thick aluminium enclosure) and is about as large as a ball point pen, making it very transportable.
Download echo audiofire 4 drivers mac os 10.8.5; alc655 536d; echo audiofire2 driver; echo audiofire 2 av/c driver; audiofire 4 driver download. ManualsAudioFire 2, AudioFire 4, AudioFire 8, AudioFire Pre8, AudioFire 12Operating SystemVersionFile SizeDate PostedWindows2.2 download1.32 MB09/25/200. Echo Digital Audio assumes no liability or responsibility for damages caused or loss incurred as a result of you downloading and using these drivers. You use this software solely at your own risk. Mac OS X (10.3.9 or later).
It works straight out of the box without any drivers on Mac OS X (haven’t tried on a Windows computer but echo’s website lists Windows XP and Vista (32 + 64 bit) compatible drivers).
If you want to use the Audiofire 4 to it’s full capabilities you’ll just have to download “Audiofire console” which is a stand alone piece of software that lets to configure the Audiofire 4: The first three tabs show the same mixing virtual console. Each tab is dedicated to a stereo output. First tab for ouput 1-2, second for 3-4 and third for the 5-6 (SPDIF out). There is also a settings tab that let you choose the sample rate, select clock source, enable/disable phantom power and also flash the firmware to the latest available version.
This software is very straightforward to use. It will also let you flash the device to the latest available firmware. Well done Echo!
Dismantling the Audiofire 4 is pretty easy. There are only 4 screws you need to remove (two at the back and two on the bottom of the device). You then have to gently slide out the main-board from the back. There is only one board inside the audio interface. It perfectly slides inside two rails that are part of aluminium frame. Simple but very clever and reliable design.
The Audiofire 4’s main-board looks well engineered and the quality of the assembly is very good. I identified the following integrated components:
- Three sharp regulators
- One Texas Instruments Firewire 1394a-2000 iceLynx controller
- One Xilink Spartan FPGA
- Two AKM 4620A CODECs (DAC and ADC converters)
- Two Analog Device SSM2019 op-amps (one for each microphone input)
- Ten JRC 2068 op-amps
Bellow are pictures of the most of the integrated components inside the Audiofire:
Echo Audiofire 12
I would definitely recommend the Echo Audiofire 4. It’s a the best good sound interface I got so far. It is well designed, sounds great (very transparent sound) and is dead easy to use! Did I mention the are reasonably priced as well (and you can them for peanuts on ebay!).
The following is the important information of Echo AudioFire Pre8 installation driver.
Driver Installation instructions for Sound Cards Only.
Echo Audiofire 4 Driver For Mac Catalina
Important!Audiofire 12 Manual
These instructions may not be applicable to other audio devices.- Click on Download Now and a File Download box will appear.
Select Save This Program to Disk and a Save As box will appear.
Select a directory to save the driver in and click Save.
Locate the driver file using Windows Explorer when the download has completed. - Running the downloaded file will extract all the driver files and setup program into a directory on your hard drive.The directory these driver are extracted to will have a similar name to the AudioFire Pre8 model that was downloaded (i.e., c:AudioFire Pre8). The setup program will also automatically begin running after extraction.However, automatically running setup can be unchecked at the time of extracting the driver file.
- Turn your computer power off.
- Connect the Echo AudioFire Pre8 to your computer.
- Turn on your computer. When the AudioFire Pre8 is first connected to the your computer, the Windows dialog called 'Add New Hardware Wizard' will appear automatically. (To display this dialog manually, you can choose the Startbutton and then Settings to access the Control Panel, and then double click on Add New Hardware. The Echo AudioFire Pre8 needs to be connected first.)
- The Add New Hardware Wizard dialog box guides you through the driver installation process. Click on Next to move from step to step.
- A dialog states 'Windows will now search for any new Plug and Play devices on your system'. Click Next.
- A subsequent dialog gives you these options:Search for the best driver for your AudioFire Pre8 (Recommended)Display a list of all drivers in a specific location, so you can select thedriver you want.Please accept the recommended choice by clicking on Next.
- The Wizard will then search your hard drive for a file called ..... *****.inf (for example AudioFire Pre8.inf). This file contains all the information that Windows needs to install the correct device drivers.
- If during installation in Windows, you will be prompted with a message warning that the driver software has not passed Windows Logo testing. Select Continue Anyway and proceed with the installation. The driver is completely tested and verified by Echo, and safe to use.
- When you see the Completing the Found New Hardware Wizard screen, click Finish to complete the driver installation.
- Once the installer has finished copying the files. You will see the Installation Complete screen. Click Finish.
- Windows will automatically continue to install the driver for Echo AudioFire Pre8.
- After you complete driver installations, you should restart your computer.
- After restarting Windows, you will see the Echo AudioFire Pre8 panel icon in your system tray (lower right corner of your desktop). Click on the icon to open the Echo AudioFire Pre8 panel.
Search and consult the Readme file for additional installation drivers instructions for your AudioFire Pre8.
- Go to Device Manager, check the devices under 'Sound, video and game controllers'. You will see the Echo AudioFire Pre8 if you have completed the installation process correctly. Your AudioFire Pre8 is ready to use.
Echo Audiofire 4 Driver For Mac Pro
Available 8 Drivers and Manual